EVK-SMARC-T335X Computer on Module Evaluation Kit
10+ Years Product Life Cycle !!
Technical & Documents Support in the product tabs.
Electronics Attributes
Form Factor 3.5 inch: 102 mm (L) x 145 (W) mm
Power Supply 3V to 5.25V
Power Consumption Typical 2W
Environment Attributes
Normal Temperature Normal Temperature: 0°C ~ 60°C
Industrial Temperature Industrial Temperature: -40°C ~ 85°C
Humidity 10% ~ 90% relative humidity, non-condensed

Write a review

Note: HTML is not translated!
    Bad           Good
Please go to Embedian Development Site for how to configure, build and install all software packages.
Yocto Project can go to Building TI/Embedian's Arago SDK Distribution for more details.
It is recommended to read our FAQs during development. 

Quick Start Guide of SMARC-T335X

These quick start guides are intended to provide developers with simple instructions on how to install SMARC T335X evaluation kit from very beginning and have it monitoring your local device in few minutes. No advanced installation options are discussed here - just the basics that will work for 95% of users who want to get started. This guide will lead you through the process of configuring, installing, and developing SMARC T335X. This guide was written to be as clear as possible and to provide only the details necessary to get you up and running. For more in-depth information, links to other chapters will be located where appropriate.
Step 1. Plug a working SD card into SD Slot (CN16)
An image pre-installed SD card comes with the evaluation kit. Plug the SD card into SD card slot (CN16). If developers do not have evaluation kit, please refer to Embedian SMARC T335X Software Installation Guide to prepare for a working SD card first.
plug your SD card in plug your SD card in
Step 2. Check Jumpers and Switches
SW1 switch should be set as SD boot (ON OFF OFF) and make sure that JP3 is not shunt.
 boot strap selectrion switch
Step 3. Wired the serial console and Ethernet cable
Connect the DB9 to RJ-45 serial console debug cable from CN14 of the evaluation board to the COM port of your PC and the Ethernet cable from LAN1 (CN4) of the device to an Ethernet switch.
 Wire Console and Ethernet Cables

Open a serial terminal like Putty in your PC. Set the COM port as 115200, 8n1.
Step 4. Power 5V to the device
Apply 5V to CN2 connector of the device. If you see the LED light on, that means the wiring is correct. Do not need to worry about the mis-wiring because the device has mis-wiring protection.
If your root filesystems is Arago. There is no password needed for root user. If your root filesystems is Ubuntu 14.04, the default root password is "root" (no quotation) and default ubuntu user password is "temppwd". Default Ethernet is set as DHCP.

EVK-SMARC-T335X Computer on Module Evaluation Kit


◆ SMARC T335X module bring-up platform for hardware and software development.

◆ SMARC T335X SMARC module validation platform

◆ Customer evaluation platform

◆ Customer carrier design reference

◆ Manufacturing test platform

◆ Flexible prototyping vehicle

◆ Computer on Module Description:

  • EVK-SMARC-T3354-600: SMARC-T3554-600 Evaluation Kit
  • EVK-SMARC-T3354-01G: SMARC-T3354-01G Evaluation Kit(+$20.0)
  • EVK-SMARC-T3354-800-I: SMARC-T3354-800-I, Evaluation Kit(+$35.0)
Datasheet download
Technical Information:
Part No. EVK-SMARC-T335X
Packing Lists

1 x SMARC T335X module

1 x SMART-BEE carrier board

4 x M2.5 screws

1 x 4GB SDHC card with image pre-installed

1 x 5V/3A Power Supply

1 x RJ45-DB9 console debug cable

1 x 10-way box header to DB9 cable


5V Power input with screw type connector and miswiring protection

Invisible reset jumper

LED backlight driver onboard

RTC backup battery


A single 4KB EEPROM is provided on I2C0 that holds the board information. This information includes board name, serial number, and revision information.

1 x external watchdog reset

Jumpers for LCD 3.3V or 5V voltage, boot selection, RS232 or RS485 selection

Form factor: 102mm (L) x 145mm (W) (3.5-inch form factor)

Networking2 x 10/100 Mbps Ethernet

18-bit and 24-bit LVDS LCD connector

2 x 10/100Mbps RJ-45 connector

1 x serial debug RJ-48 connector

1 x USB host type A connector, 1 x mini USB client connector

1 x 4-wire touch connector

1 x CAN BUS header, 2 x RS232 header (One can be configured as RS422/485), 1 x 2x7-pin GPIO header, Audio microphone and headphone header, 2 x I2C header (for capacitive touch) and 2 x SPI header

1 x SDHC connector

Power Consumption2 Watts Typical

 Linux 4.9.41 (Based on TI Processor SDK

 Linux 4.4.12 (Based on TI Processor SDK

 Linux 4.1.10 (Based on TI Processor SDK

 Linux 3.14.43 (Based on TI Processor SDK

 Linux 3.12.y (Based on TI AMSDK 7.0.1)

 Linux 3.2 (Based on TI AMSDK 6.0.0)

 Support Ubuntu 14.04/16.04 LTS or Debian 9 rootfs

 Support Yocto Project


The estimated lead time will be 5 ~10 days. For detailed lead time, please contact us.

  • Views: 4878
  • Brand: embedian
  • Product Code: EVK-SMARC-T335X
  • Availability: In Stock
  • $199.0
  • 2 or more $195.0
  • 5 or more $192.0
  • 10 or more $189.0
  • 50 or more $186.0

Available Options

Tags: embedded-computer-on-module

Features:◆ TI Sitara AM3354      ARM Cortex-A8 @600MHz, 800MHz or 1GHz◆ 512MB DD..
Features:◆ TI Sitara AM3354 @600MHz, 800MHz or 1GHz◆ 512MB DDR3◆ 4GB eMMC Flash◆ 24-b..
Features:515nm / 520nm Green Line Laser ModuleDimension Siz: D9mm x 36mmVoltage: 2.7~5VDCOutput Powe..
$60.0 $50.0
Features:515nm Small Green Laser ModuleDimension Size: D4.5mm x 8mm(without PCBA)Voltage: 2.7~5VDCOu..
$60.0 $50.0
Features:515nm standard small green laser moduleDimension Size: D6mm x 28mm(with PCBA)Voltage: 2.7~5..
$50.0 $45.0
Features:635nm Standard Small Laser ModuleDimension Size: D4mm x 18mmVoltage: 3VDCOutput Power: 1mW,..
$20.0 $16.0
Features:808nm Infrared Laser Line ModuleDimension Size: D9mm x 25mmVoltage: 3VDCOutput Power: 30mW,..
$14.0 $12.0
Features:850nm Infrared Laser ModuleDimension Size: D6mm x 10mm(without PCBA)Voltage: 3VDCOutput Pow..
$13.0 $12.0