SBC-SMART-BEE Single Board Computer
10+ Years Product Life Cycle !!
Technical & Documents Support in the product tabs.
Electronics Attributes
Form Factor 3.5 inch: 102 mm (L) x 145 (W) mm
Power Supply 3V to 5.25V
Power Consumption Typical 2W
Environment Attributes
Normal Temperature Normal Temperature: 0°C ~ 60°C
Industrial Temperature Industrial Temperature: -40°C ~ 85°C
Humidity 10% ~ 90% relative humidity, non-condensed

Write a review

Note: HTML is not translated!
    Bad           Good
Please go to Embedian Development Site for how to configure, build and install all software packages.
Yocto Project can go to Building TI/Embedian's Arago SDK Distribution for more details.
It is recommended to read our FAQs during development. 

Quick Start Guide of SMARC-T335X

These quick start guides are intended to provide developers with simple instructions on how to install SMARC T335X evaluation kit from very beginning and have it monitoring your local device in few minutes. No advanced installation options are discussed here - just the basics that will work for 95% of users who want to get started. This guide will lead you through the process of configuring, installing, and developing SMARC T335X. This guide was written to be as clear as possible and to provide only the details necessary to get you up and running. For more in-depth information, links to other chapters will be located where appropriate.
Step 1. Plug a working SD card into SD Slot (CN16)
An image pre-installed SD card comes with the evaluation kit. Plug the SD card into SD card slot (CN16). If developers do not have evaluation kit, please refer to Embedian SMARC T335X Software Installation Guide to prepare for a working SD card first.
plug your SD card in plug your SD card in
Step 2. Check Jumpers and Switches
SW1 switch should be set as SD boot (ON OFF OFF) and make sure that JP3 is not shunt.
 boot strap selectrion switch
Step 3. Wired the serial console and Ethernet cable
Connect the DB9 to RJ-45 serial console debug cable from CN14 of the evaluation board to the COM port of your PC and the Ethernet cable from LAN1 (CN4) of the device to an Ethernet switch.
 Wire Console and Ethernet Cables

Open a serial terminal like Putty in your PC. Set the COM port as 115200, 8n1.
Step 4. Power 5V to the device
Apply 5V to CN2 connector of the device. If you see the LED light on, that means the wiring is correct. Do not need to worry about the mis-wiring because the device has mis-wiring protection.
If your root filesystems is Arago. There is no password needed for root user. If your root filesystems is Ubuntu 14.04, the default root password is "root" (no quotation) and default ubuntu user password is "temppwd". Default Ethernet is set as DHCP.

SBC-SMART-BEE Single Board Computer


TI Sitara AM3354 @600MHz, 800MHz or 1GHz

◆ 512MB DDR3

◆ 4GB eMMC Flash

◆ 24-bit Parallel LCD


◆ 10/100Mbps Ethernet x 2

◆ COM x 3, USB 2.0 x 2

◆ CANbus, I2C x 3, I2S x 1, GPIO x 12

◆ Model Description:

  • SMARC-T3354-600: AM3354 Processor running at 600MHz
  • SMARC-T3354-01G: AM3354 Processor running at 1GHz
  • SMARC-T3354-800-I: AM3354 Processor running at 800MHz, industrial temperature
  • SMARC-T3354-800-I-C: AM3354 Processor, 800MHz, industrial temp., conformal coating
Datasheet download
Technical Information:
Part No. SMARC-T3354-XXX-Y-Z

 TI Sitara AM335X

 SGX530 hardware acceleration

 ARM Cortex-A8 at 600MHz, 800MHz or 1GHz


 Onboard 4GB eMMC Flash (eMMC 5.x)

 Onboard 512MB DDR3L (400Mhz x 2)

 Onboard AT24C32 EEPROM

Networking 2 x 10/100 Mbps Ethernet
Display Parallel LCD 18-bit/24-bit
Expansion 1 x SDHC/SDIO, 1 x USB 2.0 Host
USB 1 x USB 2.0 Host, 1 x USB 2.0 OTG
Additional Interface

 3 x UARTs, 2 x SPIs, 3 x I2C, 1 x I2S,

 1 x CAN Bus, RTC(Seiko S35390-A),

 3 x PWMs, 12 x GPIOs,

 4 x ADCs( for resistive touchscreen)

Power Consumption 2 Watts Typical

 Linux 4.9.41 (Based on TI Processor SDK

 Linux 4.4.12 (Based on TI Processor SDK

 Linux 4.1.10 (Based on TI Processor SDK

 Linux 3.14.43 (Based on TI Processor SDK

 Linux 3.12.y (Based on TI AMSDK 7.0.1)

 Linux 3.2 (Based on TI AMSDK 6.0.0)

 Support Ubuntu 14.04/16.04 LTS or Debian 9 rootfs

 Support Yocto Project


The estimated lead time will be 5 ~10 days. For detailed lead time, please contact us.

  • Views: 3893
  • Brand: embedian
  • Product Code: SBC-SMART-BEE
  • Availability: In Stock
  • $134.0
  • 10 or more $130.0
  • 50 or more $127.0
  • 200 or more $125.0
  • 500 or more $123.0

Available Options

Tags: embedded-computer, single-board-computer

Features:◆ TI Sitara AM3354      ARM Cortex-A8 @600MHz, 800MHz or 1GHz◆ 512MB DD..
Features:◆ SMARC T335X module bring-up platform for hardware and software development.◆ SM..
Features:515nm / 520nm Green Line Laser ModuleDimension Siz: D9mm x 36mmVoltage: 2.7~5VDCOutput Powe..
$60.0 $50.0
Features:515nm Small Green Laser ModuleDimension Size: D4.5mm x 8mm(without PCBA)Voltage: 2.7~5VDCOu..
$60.0 $50.0
Features:515nm standard small green laser moduleDimension Size: D6mm x 28mm(with PCBA)Voltage: 2.7~5..
$50.0 $45.0
Features:635nm Standard Small Laser ModuleDimension Size: D4mm x 18mmVoltage: 3VDCOutput Power: 1mW,..
$20.0 $16.0
Features:808nm Infrared Laser Line ModuleDimension Size: D9mm x 25mmVoltage: 3VDCOutput Power: 30mW,..
$14.0 $12.0
Features:850nm Infrared Laser ModuleDimension Size: D6mm x 10mm(without PCBA)Voltage: 3VDCOutput Pow..
$13.0 $12.0